What the lights on a NOCO Boost mean
The red exclamation point is the Error LED. On a GB20 to GB150, solid red means the clamps are reversed and blinking red means the internal battery is too hot. On a Boost X (GBX45 to GBX155) it blinks one to six times, and the number of blinks tells you which error it found.
Checked against sources on by the TrueAmps editorial team.
Boost GB20, GB40, GB70, GB150
NOCO's support pages for all four models list the same lights and the same three faults.
| What you see | What NOCO says it means | What to do |
|---|---|---|
| Red exclamation (Error LED), solid | Reverse polarity | Swap the clamps |
| Red exclamation, blinking, clamps on correctly | Internal battery too hot | Let it cool, move it somewhere cooler |
| Boost LED stays off, clamps on correctly | Vehicle battery below 2 volts | Remove all loads and try again, or use Manual Override |
| Boost LED flashing white | Manual Override is on | See the warning below |
| Power LED white | Unit is on | Nothing |
From NOCO's support pages for the GB40, GB20, GB70 and GB150, checked October 26, 2026. The red exclamation symbol is how NOCO draws the Error LED on those pages.
Boost X GBX45, GBX55, GBX75, GBX155: blink codes
On the Boost X the Error LED counts. Reverse polarity has its own red light, and temperature has a pair of hot and cold lights.
| Error LED | What NOCO says it means | What to do |
|---|---|---|
| Solid red | Reverse polarity | Swap the clamps |
| 1 flash | Short circuit at the clamps | Remove all loads, reconnect the clamps |
| 2 flashes | High voltage at the clamps, such as a 24 V system | No fix listed; NOCO rates the Boost X for 12 V batteries |
| 3 flashes | Bad internal battery cell, found during charging | No fix listed by NOCO |
| 4 flashes | Charge timeout: in bulk charge for too long | No fix listed by NOCO |
| 6 flashes | Back-charge through the clamps in Manual Override, such as a 24 V system | No fix listed; 12 V batteries only |
NOCO's table has no entry for five flashes. From the GBX45 support page; the GBX155 page lists the same codes. Checked October 26, 2026.
| Other Boost X lights | What NOCO says it means |
|---|---|
| Hot LED (red), solid | Working, but close to its upper temperature limit. Let it cool. |
| Hot LED (red), flashing | Too hot to jump start; only the flashlight works. Let it cool. |
| Cold LED (blue), solid | Working, but close to its lower temperature limit. Let it warm up. |
| Cold LED (blue), flashing | Too cold to jump start; only the flashlight works. Let it warm up. |
| Power LED orange | The 60-second jump start countdown has ended. Power off and on to start again. |
| Fast Charge LED white | Fast charging is on (over 15 W, USB-C Power Delivery 3.0) |
| Fast Charge LED flashing red | Check the cable, charger or the USB-C device for damage |
| Fast Charge LED solid red | Incompatible charger: unplug, power off and on, try another charger |
A red light while it charges
Four charge LEDs show the level of the internal battery. NOCO draws the first two in red, the third in orange and the last in green. While a GB unit recharges, the LEDs pulse slowly and turn solid one by one. When it is full, the green 100% LED stays on and the other three go off; NOCO says the green LED pulses now and then while it maintains the charge (GB40 user guide). So a red LED pulsing during a recharge is the charge level, not a fault.
On a Boost X, the light to watch while charging is the Fast Charge LED. Red there is an error, as the table above shows.
Resetting it
NOCO's GB40 page gives the reset in one line: power off, then on. On a Boost X the same power cycle starts a new 60-second jump start window (GBX45 user guide). NOCO's guide also says not to try more than five jump starts in a row within 15 minutes, and to let the unit rest for 15 minutes before trying again. A reset does not clear the cause, so swap reversed clamps or let a hot unit cool before you power it back on.
Manual Override
When the Boost LED stays off because the vehicle battery is under 2 volts, NOCO provides Manual Override: hold the button for three seconds. NOCO's warning is that it disables the safety protection and forces boost on, and that it is only for a battery too low to be detected. Check the polarity before you press it.
The full sequence, from attaching the clamps to switching off, is on how to use a NOCO Boost. Charger lights work differently; those are on NOCO GENIUS lights. NOCO's Boost Air AX65, which adds a tire inflator, is covered on jump starters with a built-in air compressor.
Sources
- NOCO support pages, LEDS and Troubleshooting sections: GB40, GB20, GB70, GB150, GBX45, GBX155. Checked October 26, 2026.
- GB40 user guide (03.07.2025A) and GBX45 user guide (02.07.2024): charging LEDs, 60-second timeout, jump start limits.
Questions people ask
Why is there a red exclamation point on my NOCO Boost?
That symbol is the Error LED. On a GB20, GB40, GB70 or GB150, NOCO says solid red means the clamps are on the wrong terminals and blinking red means the internal battery is too hot. On a Boost X it blinks one to six times, and the count names the error.
Why is my NOCO Boost flashing red while it charges?
On the GB models the charge LEDs pulse while the unit recharges, and NOCO draws the first two of them in red. A pulsing red LED there is the charge level, not an error. On a Boost X, a red Fast Charge LED is an error: flashing means check the cable or charger for damage, solid means the charger is incompatible.
How do I reset the error light on a NOCO Boost?
NOCO's GB40 page says to power the unit off and on again to reset it. Fix the cause first: swap reversed clamps, or let a hot unit cool down.
What does the orange power light on a NOCO Boost X mean?
The 60-second jump start countdown has run out. NOCO says to power the unit off and back on to start a new jump start sequence.